IGLA-PRO Anti Theft Support | Bible
Welcome to the IGLA-PRO Installation Support Bible.
Valet Mode | Service Mode
To enter valet mode do the following:
- Turn Ignition ON
- Authorize via PIN Code (ENTER YOUR PIN CODE)
- Press and release service button 5 times
Note: Valet mode automatically shuts off if vehicle driven over 50 kmh, OR 15+ minutes of actual driving. You can also disable valet mode by entering your PIN code again.
Key Fob Programming
To pair a new keyfob, follow these steps:
1. Retrieve batteries from all keyfobs (including those
paired with the system).
2. Turn off Bluetooth on smartphones paired with the
system.
3. Turn on ignition.
4. Put the system into the PIN Change mode.
The service indication signal will be repeating once
every 3 seconds.
5. Push the service button twice.
6. Push and hold the button on the keyfob body.
7. Insert the battery and release the button. The keyfob
LED will start blinking green once per second.
If successful, keyfob pairing will be confirmed with
the LED blinking red once.
If unsuccessful, the LED will stop blinking green in
30 seconds.
8. Turn off ignition.
User Guide & Install Guide
Downloaded upon choosing the product being installed. When you choose your vehicle during programming, the install guide will show up.
CLICK HERE for ALL Guides
INSTALLATION INSTRUCTIONS
Ground unit
Connect BROWN (1CANH) to vehicle
Connect WHITE (1CANL) to vehicle
*IF AVAILABLE*
Connect PINK (2CANH) to vehicle - Firmware Dependent
Connect GREEN (2CANL) to vehicle - Firmware Dependent
Power up Red to Constant 12v WITH GRAY WIRE.
Turn ignition on
INDICATION SIGNS will light up/beep every 2 secs.
AT THIS POINT ENTER YOUR DESIRED PIN CODE
WAIT
IT WILL FLASH/BEEP 3TIMES to prompt you to enter your PIN CODE AGAIN
REPEAT DESIRED PIN CODE
WAIT
IT WILL FLASH/BEEP 2TIMES. This is to confirm that the pincode is set.
THE INDICATION will no longer flash/beep.
TURN IGNITION OFF.
DISCONNECT GRAY WIRE.
ATTEMPT TO START THE VEHICLE. IF ENGINE INHIBIT IS ON, VEHICLE SHOULD NOT START
Turn car off.
Turn car to IGNITION.
ENTER PIN CODE.
INDICATORS should beep/flash TWICE to acknowledge PIN CODE is accepted.
START THE VEHICLE, At this point the vehicle SHOULD STAY RUNNING AND IS GOOD TO DRIVE AWAY.
Turn vehicle off.
Install battery into 1 of the 2 keyfobs.
Test to make sure the indicator flashes twice to acknowledge authorization via KEYFOB.
Remove battery from keyfob 1.
Install Battery into the 2nd keyfob.
Test to make sure the indicator flashes twice to acknowledge authorization via KEYFOB.
Firmware Programming
You must use the IGLA USB key firmware programming tool:
To access firmware programming, visit the link below:
http://new.service.author-alarm.ru/global-en
Key Tag Range Adjustments
If the key tag range is too high (as in the tag keeps the vehicle disarmed from too far away (default range is approx. 25 - 30 feet), you can shorten this range via mobile phone using Bluetooth or via desktop software, by putting the IGLA into service mode and making a Bluetooth connection with the smartphone (which has the IGLA app), inside the app there are range settings.
What to do if vehicle has OEM remote starter?
Toyota 4Runner 2016 - 2019
The 4Runner is not listed in the IGLA application guide, so you must program as Toyota Land Cruiser Prado (J150)
*Note* We have found the latest firmware version can be glitchy, so roll back to previous version
Confirmation lights via the infotainment screen goes from P Park to S (Sports?) to P Park. This display will confirm that the code entered has been accepted.
Subaru Forester
2020 - Up Subaru Foresters must be programmed as a 2019
*Note* We have found the latest firmware version can be glitchy, so roll back to previous version
Confirmation light is the parking brake light, which will flash on/off/on to confirm code has been accepted.